UY-991D-ESD-110V 智慧型SMD無鉛熱風拆焊機ESD (符合RoHS規範) Intelligent Lead-free Rework Welder SMD ESD (RoHS compliant)
功能特性 Features
待機休眠 Standby hibernation
熱風握柄具有磁控開關控制,放置於握柄固定架上,立即停止加溫,吹送大量冷風,待溫度降至100℃時,
進入待機休眠狀態,可延長發熱器使用壽命;觸動熱風握柄,立即快速升溫至原設定溫度及風量。
Heat Gun’s handle with magnetic switch control ,when it place on the holder ,the heat gun will stop heating immediately and blowing a large number of cold wind then the temperature be dropped to 100 ℃.
Into standby hibernation, extend the life of the heater , when you touch the heat gun's handle , immediately it will be heating to the original set temperature and blowing rate .
密碼保護及按鍵鎖定 Password protection and Key lock
可設定密碼,進行面板控制按鍵鎖定,有效防止人員任意更改設定溫度。
It can set a password and have the panel key lock . This can effectively prevent any changes to the set temperature staff.
三個工作溫度設定 Three temperature settings
自行設定CH1、CH2、CH3 三個工作通道,每組工作通道的溫度、風量;方便拆取不同元件,使用不同的作業參數。
You can set CH1, CH2, CH3 three working channels by yourself. Then you can set temperature and the blowing rate in each working channel.
It is easy to cannibalize the different components, the use of different operating parameters.
無碳刷渦輪馬達 Brushless motor turbine
本設備採用無碳刷渦輪馬達,大流量、低風壓,使用壽命長。可以完全避免碳刷的使用耗損及碳粉的污染源。
This equipment uses a turbine motor brushless, large flow、low air pressure, long life.
You can completely avoid the use of toner depletion and pollution carbon brushes.
大功率大風量 High-Power & High-Blowing Rate
感溫器測溫迴路,控制溫度輸出。1000W 大功率輸出,升溫迅速,不受風量影響,輸出溫度精確穩定;數位化溫度校準方式,操作便捷迅速。
輸出風量可達120 l/min。能滿足所有SMD 表面黏著元件,快速拆焊無鉛製程。
Temperature sensor temperature measurement circuit can control the
temperature output.
1000W power output, rapid heating, blowing rate can’t affect it , the output temperature accuracy and stability.
It is digitized temperature calibration mode, the operation fast and easy.
The output of wind of up to 120 l / min,it can satisfy all SMD surface mount components, rapid desoldering lead-free process.
熱風頭 & 固定架 Nozzle & Holder
主機配置單管熱風頭1 只。更換不同尺寸熱風頭,不需使用工具,更換方便、迅速。
CB-800L 熱風握柄昇降台及PC 板固定架,為另選購配件。
Host computer ‘s Configuration is one single-tube nozzle.
If you want to change to different sizes of nozzle without the use of tools to facilitate the replacement quickly.
CB-800L Lifting platforms and PC board holder both are optional accessories.
ESD & RoHS
靜電防護設計。本設備原物料,採用符合RoHS 規範。
This is ESD protection design. Our equipment raw materials, which is the use of RoHS compliant.
規格 Specification
MODLE |
VECTECH 991D |
Input Voltage |
AC110V / 230V |
Power |
1000 W |
Dimensions MM/Weight KG |
188(L)*245(D)*135(H)/3.65 |
Temperature Range |
100℃ ~ 500℃ |
Airflow Range |
1 ~ 120 l/min |
The maximum amount of wind |
120 l/min |
Security Features |
Lock temperature. Magnetron standby hibernation |
|