UY-990D-ESD-110V 智慧型SMD無鉛熱風拆焊機ESD (大功率大流量) Intelligent Lead-free Rework Welder SMD ESD (High-Power & High-Blowing Rate)
功能特性 Features
大型液晶顯示Large LCD
大尺寸液晶顯示視窗,顯示工作設定參數,如: 工作時間、溫度、風量、休眠、鎖溫,工作通道等等,10種參數。
This is the large LCD window which displays the work of setting, for example: working time, temperature, capacity of wind, standby hibernation, lock temperature and the working channel…etc . Here are ten parameter.
雙重控制 待機休眠 Standby hibernation / Standby hibernation
可選擇設定腳踏開關控制或磁控開關控制。選擇磁控開關控制時,熱風握柄放置於握柄固定架上,立即停止加溫,吹送大量冷風,待溫度降至100℃時,進入待機休眠狀態,可延長發熱器使用壽命;觸動熱風握柄,立即快速升溫至原設定溫度及風量。選擇腳踏開關控制作業時,再次觸動腳踏開關,即可停止加溫,吹送冷風至100℃時,呈待機休眠狀態。選擇腳踏開關控制作業時,再次觸動腳踏開關,即可停止加溫,吹送冷風至100℃時,呈待機休眠狀態。
Here are two choices, one is set foot switch control the other is magnetic switch control. When you select magnetic switch control ,heat Gun’s handle with magnetic switch control , it place on the holder ,the heat gun will stop heating immediately and blowing a large number of cold wind then the temperature be dropped to 100 ℃.
Into standby hibernation, extend the life of the heater , when you touch the heat gun's handle , immediately it will be heating to the original set temperature and blowing rate .
Select foot switch control, when you touch the foot switch control again, it will stop heating, blowing cold air to 100 ℃, show standby hibernation.
密碼保護及按鍵鎖定Password protection and Key lock
可設定密碼,進行面板控制按鍵鎖定,有效防止人員任意更改設定溫度。
It can set a password and have the panel key lock . This can effectively prevent any changes to the set temperature staff.
三個工作溫度設定Three temperature settings
自行設定CH1、CH2、CH3 三個工作通道,每組工作通道的溫度、風量;方便拆取不同元件,使用不同的作業參數。
You can set CH1, CH2, CH3 three working channels by yourself. Then you can set temperature and the blowing rate in each working channel.
It is easy to cannibalize the different components, the use of different operating parameters.
無碳刷渦輪馬達Brushless motor turbine
本設備採用無碳刷渦輪馬達,大流量、低風壓,使用壽命長。可以完全避免碳刷的使用耗損及碳粉的污染源。
This equipment uses a turbine motor brushless, large flow、low air pressure, long life.
You can completely avoid the use of toner depletion and pollution carbon brushes.
大功率大風量 High-Power & High-Blowing Rate
感溫器測溫迴路,控制溫度輸出。1300W 大功率輸出,升溫迅速,不受風量影響,輸出溫度精確穩定;數位化溫度校準方式,操作便捷迅速。風量輸出為可調式,最大風量達200 l/min,低風壓輸出,拆焊元件過程,週邊零件不易產生位移。滿足無鉛製程SMD表面黏著元件,快速拆焊工具。
Temperature sensor temperature measurement circuit can control the
temperature output.
1300W power output, rapid heating, blowing rate can’t affect it , the output temperature accuracy and stability.
It is digitized temperature calibration mode, the operation fast and easy.
The air output is adjustable,the output of wind of up to 200 l / min,it can satisfy all SMD surface mount components, rapid desoldering lead-free process.
ESD
靜電防護設計。
This is ESD protection design.
規格 Specification
MODLE |
990D |
Input Voltage |
AC110V / 230V |
Power |
1300 W |
Dimensions MM/Weight KG |
250(L)*230(D)*150(H)/3.8 |
Temperature Range |
100℃ ~ 500℃ |
Airflow Range |
6 ~ 200 l/min |
The maximum amount of wind |
200 l/min |
Security Features |
Lock temperature. Magnetron standby hibernation |
|